Showing 1985–2000 of 2002 resultsSorted by latest
-
REQUEST A QUOTE
- Brand: ABB
- Model Number: DSQC3060
- Product Type: FlexPendant / Teach Pendant
- Product Net Weight: 1.5 kg (approx. 3.3 lbs)
- Gross Weight: 2.0 kg (approx. 4.4 lbs)
- Primary Interface Components: Color touch screen, emergency stop button, enabling device (deadman switch), multi-axis joystick
- Joystick Assembly: The precise multi-axis joystick assembly can also be isolated and replaced under independent component sourcing if mechanical drift occurs during long-term manual robot programming cycles.
ABB 3HAC064211-001 DSQC3060 FlexPendant (Teach Pendant) (OmniCore).
-
REQUEST A QUOTE
- Component Type: Local I/O Digital Base Module
- Digital Inputs: 16 Digital Inputs (24 VDC)
- Digital Outputs: 16 Digital Outputs (24 VDC)
- Communication Protocol: Native EtherNet/IP (No extra software option license needed)
- Dimensions: 75 mm × 36 mm × 101 mm (L × W × H)
- Weight: ~0.12 kg (120 grams)
- Mounting: DIN rail standard (via bracket 3HAC062073-001)
- Daisy-Chaining Capabilities: The modular baseline architecture allows engineers to daisy-chain up to four extension modules directly to this base block. Compatible modules include the DSQC1031 (Digital Add-on), DSQC1032 (Analog Add-on), and DSQC1033 (Relay Add-on).
- Wiring Criticality: The unit communicates over standard native EtherNet/IP. When wiring your cabinet layout (e.g., standard C30 or V20 cabinet footprints), ensure that the target I/O signal power loop is fully closed and active; otherwise, the main robot processor will fail to successfully scan the bus layout. If scanning drops, a hardware master reset button is located directly on the face of the DSQC1030.
ABB 3HAC058663-001 DSQC1030 Local I/O Digital Base Module (IRC5 / OmniCore).
-
REQUEST A QUOTE
- ABB Type Designation: DSQC1030 Local I/O Digital Base
- I/O Capacity: 16 Digital Inputs / 16 Digital Outputs
- Communication Protocol: Native EtherNet/IP protocol support (daisy-chainable up to 4 modules)
- Input Voltage: 24 VDC
- Weight: ~0.12 kg to 0.19 kg
- Country of Origin: Sweden
- Required Accessories: Shipped without connectors. Connector set 3HAC060919-001 must be purchased separately.
- Daisy Chaining: Because the module features native EtherNet/IP architecture, you can expand your workspace I/O by daisy-chaining up to four total DSQC1030 modules without needing extra licensing for basic communication.
- Mounting: The unit interfaces directly onto a standard DIN bracket (ABB support part 3HAC062073-001) inside your drive module or controller cabinet.
ABB 3HAC058663-001 Local I/O Digital Base Module (IRC5 / OmniCore).
-
REQUEST A QUOTE
- Manufacturer: ABB
- Part Number (MPN): 3HAC029818-001
- Model Designation: DSQC 663 (MDU-790A HV / HV6P)
- Application: 6-Axis Servo Drive & Motion Control
- Cabinet Compatibility: ABB IRC5 Controller
- Built-in Protections: Overvoltage, Overcurrent, Overheating, Short-Circuit
- Net Weight: 12.33 kg (27.18 lbs)
- Country of Origin: Estonia / Sweden / Switzerland (Varies by manufacturing lot)
- Medium Payload: IRB 2400 / IRB 2600
ABB 3HAC029818-001 DSQC663 Servo Drive Module (Main Drive Unit) (IRC5 Robot Controller).
-
REQUEST A QUOTE
- Channels: 16 digital input channels, divided into 2 individually isolated groups (8 channels + 1 voltage supervision input per group)
- Rated Input Voltage: 24 V DC (Sink type input configuration)
- Input Voltage Range: Signal (0): -30 to +5 V
- Input Current / Impedance: 6 mA typical at 24 V / Input Impedance: 3.5 kΩ
- Selectable Filter Times: 2 ms, 4 ms, 8 ms, or 16 ms
- Power Dissipation: 1.8 W (Typical)
- Isolation Rating: 50 V rated insulation voltage; 500 V AC dielectric test voltage
- Compatible Module Termination Units (MTUs): TU810, TU812, TU814, TU818, TU830, TU833, TU838, TU850
- Process Voltage Supervision: Each of the two isolated channel groups incorporates a process voltage supervision input. If the external 24 V process power loop fails or drops, a channel error signal is immediately broadcasted via the ModuleBus for quick diagnostic troubleshooting.
- Robust Signal Protection: Every channel features current-limiting hardware, built-in Electro-Magnetic Compatibility (EMC) protection components, an optical isolation barrier, and an active status indication LED.
ABB 3BSE008508R1 DI810 Digital Input Module (S800 I/O).
-
REQUEST A QUOTE
- Manufacturer: ABB (Asea Brown Boveri)
- Global Order Code / SKU: 1SVR405633R1100
- Relay Family Range: CR-MX (Pluggable Miniature Range)
- Contact Configuration: 4 c/o (SPDT) (4 Change-Over / Single Pole Double Throw contacts)
- Rated Output / Load Current: 5 A at 250 V AC (Note: Some manufacturing sheets list peak limits up to 7 A)
- Physical Pin Count: 14 Pins (Flat blade style plug-in design)
- Diagnostics Sub-Function: Integrated LED Indicator (Lights up when the coil is energized for easy troubleshooting)
- Environmental Compliance: RoHS Directive 2011/65/EU
- Visual Status Monitoring: The built-in LED provides immediate physical confirmation of control loop status without requiring manual multimeter probing.
- Modular Assembly: Designed to sit inside matching standard 14-pin DIN-rail mount sockets. It supports pluggable function modules (such as RC elements or varistor surge suppressors), mechanical holders, and identification markers.
ABB CR-MX024DC4L DC24V Pluggable Interface Relay (CR-M Series).
-
REQUEST A QUOTE
- ABB Article ID / EAN: 1SFA619100R1112 / 7320500550717
- Mounting Hole Diameter: 22.3 mm (Standard 22 mm panel cutout)
- Physical Dimensions: 30 mm × 30 mm × 55 mm (W × H × D)
- Net Weight: 0.018 kg (0.63 oz)
- Contact Configuration: 1 NO (Normally Open), 0 NC
- Operating Voltage: 24 V AC/DC (for the integrated green LED)
- Ingress Protection: IP20 (Terminals), IP66 / IP67 / IP69K (Front face)
- NEMA Enclosure Ratings: NEMA 1, 3R, 4, 4X, 12, 13
- Mechanical Durability: 500,000 operations (0.5 million cycles)
- Terminal Connections: Threaded screw clamp terminals
ABB CP1-11G-10 Illuminated Pushbutton Switch (Compact Range).
-
REQUEST A QUOTE
- Measuring & Supply Voltage: 3×300 to 500 V AC (50/60 Hz), self-powered from line
- Output Type: 2 c/o (DPDT / Change-over) contacts
- Contact Rating: 250 V AC / 4 A
- Tripping Delay Time: Adjustable from 0 s (instantaneous) up to 30 s
- Delay Behavior: Selectable ON-delay or OFF-delay configuration
- Terminal Connection: Screw terminals with double-chamber cage clamps
- Mounting Style: Standard 35 mm DIN Rail
- Protection Degree: Housing: IP50 | Terminals: IP20
- Approvals / Standards: CE, cULus, EAC, CCC, IEC 60255-27, Railway Approved
- R (Yellow): Indicates the state of the output relay contacts.
ABB CM-PVS.41S Three-Phase Monitoring Relay (CM Series).
-
REQUEST A QUOTE
- Product ID / Code: 1SVR550871R9500
- Measuring / Supply Range: 320–460 V AC (L₁-L₂-L₃)
- Rated Frequency: 50 / 60 Hz
- Output Contact: 1 N/O (Normally Open)
- Contact Rating: 250 V / 4 A
- Response Time: 80 ms
- Hysteresis: 5%
- Housing Width: 22.5 mm
- Connection Type: Screw Terminals
- Phase Loss Detection: Instantly drops the output relay if any of the three phases fail completely.
ABB CM-PVE 3×320-460VAC Three-Phase Monitoring Relay (CM Series).
-
REQUEST A QUOTE
- Phase Loss Monitoring: Protects downstream equipment (such as three-phase motors) from running on a missing phase, which causes severe overheating and immediate winding damage.
- Overvoltage & Undervoltage Protection: Monitors the mains voltage to ensure it stays within a safe, fixed window. If the voltage swings outside the nominal thresholds, it trips to prevent insulation breakdown or equipment brownouts.
- Interrupted Neutral Monitoring: Ensures that single-phase loads tied to the neutral wire are protected from unpredictable voltage fluctuations or floating neutrals.
- Manufacturer: ABB
- Measuring & Supply Voltage: Phase-to-Neutral (L-N):
- Output Configuration: 1 N/O (Normally Open) output contact
- Output Contact Rating: 250 V / 4 A (AC-12 resistive load)
- Threshold Adjustments: Fixed (Non-adjustable windows)
- Connection Capacity: Rigid / Flexible: 2x 18-16 AWG
- Tightening Torque: 7.08 in⋅lb (0.8 N⋅m)
ABB CM-PVE 185-265VAC Three-Phase Monitoring Relay (CM Series).
-
REQUEST A QUOTE
- Frequency Range: 50 / 60 Hz
- Output Contacts: 2 c/o (SPDT changeover)
- Contact Rating: 250 V / 4 A
- Monitored Parameters: Phase Failure & Phase Sequence
- Response Time Delay: 500 ms
- Terminal Connection: Screw Terminals
- Mounting Type: DIN Rail Mountable
- Enclosure Rating: IP50 (Housing) / IP20 (Terminals)
- Self-Powered Efficiency: The relay does not require an external power supply; it is directly powered from the L1-L2-L3 measuring voltage lines.
- Phase Sequence Monitoring: Ensures that the phases are in the correct sequence (L1-L2-L3). If a sequence is inverted (which can cause three-phase motors to rotate backwards), the relay de-energizes.
ABB CM-PFS.S Three-Phase Monitoring Relay (CM Series).
-
REQUEST A QUOTE
- Phase Failure (Phase Loss): Instantly detects if one of the three phases goes completely dead or falls below fixed operational thresholds, preventing motors from "single-phasing" (which causes catastrophic winding burnouts).
- Phase Sequence: Ensures that the physical phase rotation matches the expected sequence (L1-L2-L3). If the rotation is reversed, the relay trips to prevent industrial equipment—like motors, pumps, and compressors—from spinning backwards and destroying themselves.
- Metric / Parameter: Specification Details
- Product ID (Standard): 1SVR550824R9100
- Frequency Range: 50 / 60 Hz
- Output Type: 1 c/o (SPDT / Changeover) contact operating on the closed-circuit principle
- Contact Rating: Maximum 250 V / 4 A
- Time Delay Response: ≈ 500 ms start-up/fault delay (fixed thresholds)
- Environmental Temperature: -20°C to +60°C (operational)
- Physical Dimensions: 22.5 mm (W) x 78 mm (H) x 78.5 mm (D)
ABB CM-PFE Three-Phase Monitoring Relay (CM Series).
-
REQUEST A QUOTE
- Catalog Number / Product ID: 1SVR550882R9500
- UPC / EAN: 4013614348136
- Measuring & Control Supply Voltage: 380–440 V AC (L₁, L₂, L₃ Line-to-Line, 50/60 Hz)
- Output Type: 1 Normally Open (N/O) contact, working on the closed-circuit principle
- Contact Rating: 250 V / 4 A
- Fixed Trip Threshold: Phase failure occurs when measuring voltage drops below 60% of rated voltage
- Timing Parameters: 500 ms start-up delay / 150 ms tripping delay
- Terminal / Mounting Type: Screw terminals; Snap-on mounting for standard DIN Rail (TH35)
- Status Indicators: Yellow LED for Relay Status (R)
- Compliance / Standards: UL 508, CAN/CSA C22.2 No.14, IEC/EN 61000-6-2/3, RoHS
ABB CM-PBE 3×380-440VAC Three-Phase Monitoring Relay (CM Series).
-
REQUEST A QUOTE
- Catalog / Part Number: CM-PAS.41S / 1SVR730774R3300
- Measuring Voltage Range (L-L): 300 to 500 V AC (50/60 Hz)
- Monitored Parameters: Phase Failure, Phase Sequence, Phase Unbalance (Asymmetry)
- Output Contacts: 2 c/o (DPDT / Double Pole Double Throw) contacts
- Output Contact Rating: 250 V AC / 4 A (Resistive / AC-12)
- Tripping Time Delay: Adjustable ON-delay (0 s or 0.1 to 30 s)
- Response Time: < 100 ms on fault detection
- Terminal Connection Type: Screw Technology (Double-chamber cage connection terminals)
- Mounting Format: 35 mm DIN Rail (Top hat rail according to IEC/EN 60715)
- Operating Temperature: -25 °C to +60 °C (-13 °F to +140 °F)
ABB CM-PAS.41S Three-Phase Monitoring Relay (CM Series).
-
REQUEST A QUOTE
- Catalog / Order Number: 1SVR730884R3300
- Measuring & Supply Voltage (L-L): 300 to 500 V AC, 50/60 Hz
- Output Contacts: 2 c/o (SPDT / DPDT) relays rated at 250 V / 4 A
- Tripping Delay Range: Adjustable from instantaneous (0 s) up to 30 s
- Connection Technology: Double-chamber cage screw terminals
- Mechanical Life: > 10 million operations
- Environmental Protection: IP20 (Housing) / IP40 (Front panel face)
- Operating Temperature Range: -25°C to +60°C
- Physical Dimensions: 22.5 × 85.6 × 103.7 mm (W × H × D)
- Over- and Undervoltage Monitoring: Detects when phase voltage exceeds or drops below safe, custom-configured constraints.
ABB CM-MPS.41S Three-Phase Monitoring Relay (CM Series).
-
REQUEST A QUOTE
- Rated Measuring Voltage: 3×350 to 580 V AC, 50/60 Hz
- Output Contacts: 2 c/o (DPDT) rated at 250 V / 4 A
- Adjustable Off-Delay Time: 0.1 to 30 seconds
- Power Supply: Powered directly via the measuring circuit (No external power required)
- Mounting Format: Standard DIN Rail installation
- Operating Temperature: -25°C to +60°C
- Safety Approvals: GL, UL (Suitable for industrial & railway applications)
- Overvoltage & Undervoltage: Features adjustable threshold values.
- Phase Failure Detection: Instantaneous trip during the loss of any operational phase.
- Phase Unbalance / Imbalance: Protects motors against thermal loads caused by asymmetrical supply networks.
ABB CM-MPN.52S 1SVR750487R8300 Three-Phase Monitoring Relay (CM Series).
