Showing 17–32 of 49 results
-
- Manufacturer: AUTONICS
- Model / Part Number: E50S8-2048-6-L-5
- Sensing Technology: Optical incremental
- Starting Torque: Max. 70 gf·cm (0.00686 N·m)
- Power Voltage: 5VDC ±5% (Max 5% ripple P-P)
- Connection Type: Axial cable type
- Protection Structure: IP50 (IEC standard)
-
- Manufacturer: AUTONICS
- Model / Part Number: E50S8-300-3-T-24
- Resolution: 300 P/R (Pulses per Revolution)
- Output Phases: 3 channels (A, B, Z)
- Control Output: Totem pole output
- Power Supply Voltage: 12-24VDC ±5% (ripple P-P: max. 5%)
- Shaft Diameter: Ø8 mm
- Diameter of Housing: 50 mm
- Connection Type: Axial cable type
- Starting Torque: Max. 70 gf·cm (Max. 0.00686 N·m)
- Protection Structure: IP50 (IEC standard)
-
- Manufacturer: AUTONICS
- Model / Part Number: E50S8-360-3-T-24
- Series: E50S
- Resolution: 360 pulses per revolution
- Shaft Diameter: 8 mm
- Output: Totem-pole output
- Supply Voltage: 12–24 VDC
-
- Manufacturer: AUTONICS
- Model / Part Number: E50S8-3600-3-T-24
- Resolution: 3,600 Pulses per Revolution (P/R)
- Shaft Diameter: Ø8 mm
- Control Output: Totem pole type
- Output Phases: 3 Phases (A, B, Z)
- Power Supply: 12–24VDC ±5%
- Connection Type: Axial cable type
- Max Rotation: 5,000 RPM
- Max Frequency: 300 kHz
- Ingress Protection: IP50 rating
-
- Manufacturer: AUTONICS
- Model / Part Number: E50S8-600-3-T-24
- Output Type: Totem pole (works with many types of controllers like PLCs)
- Output Phases: A, B, Z (A and B measure speed/direction; Z provides a reference zero-point)
- Max Speed: 5,000 revolutions per minute (RPM)
- Max Frequency: 300 kHz (maximum speed it can send pulses safely)
- Connection Type: Axial cable type (a 2-meter wire comes directly out of the back)
- Weather Protection: IP50 rating (protected against dust, but not waterproof)
-
REQUEST A QUOTE
- Output Type: Totem pole (Push-Pull)
- Supply Voltage: 12–24 VDC ± 5% (ripple P-P: max. 5%)
- Resolution: 1 pulse per 1 mm
- Number of Pulses: 250 pulses per revolution
- Wheel Circumference: 250 mm
- Output Phases: A, B (Allows direction sensing)
- Connection Type: Axial cable type (pre-wired)
- Protection Rating: IP50 (Indoor/Dust-resistant environment)
AUTONICS ENC-1-1-T-24 Wheel-Type Encoder (ENC Series).
-
REQUEST A QUOTE
- Display Method: 4-digit 7-segment LED
- Operating Voltage: 100–240 VAC ~ 50/60 Hz
- Terminal / Base Type: 8-Pin Plug (Requires an external socket)
- Control Output: SPDT (1c) Relay Output: 5A at 250 VAC
- Timing Range: Ultra-wide range from 0.01 seconds up to 9999.9 hours
- Operation Methods: Count up, Count down
- Output Modes: Power On Delay, Flicker
- Memory Protection: Built-in non-volatile semiconductor memory (retention up to 10 years)
- Environmental Rating: IP20 protection structure (front panel)
- Flexible Input Signal Configuration: Built-in internal DIP switches allow users to switch easily between voltage inputs (PNP) and no-voltage inputs (NPN) depending on sensor type requirements.
AUTONICS FS4E-1P4 Digital Timer (FSE Series).
-
REQUEST A QUOTE
- Specification Attribute: Details & Performance Metrics
- Display Method: 4-digit, 7-segment LED display
- Operation Method: Counter: Count up, Count down, Count up/down
- Timer: Count up, Count down
- Power Supply: 100 to 240 V AC (± 10%), 50/60 Hz
- External Sensor Power: Maximum 12 V DC (± 10%), 50 mA
- Counting Speeds: Selectable: 1 cps, 30 cps, 2 kcps, 5 kcps
- Signal Input: Voltage input (PNP) or No-voltage input (NPN) via internal DIP switches
- Memory Protection: Approximately 10 years (Non-volatile EEPROM)
- Dimensions & Mounting: W72mm × H36mm panel mount format
AUTONICS FX4Y-I4 Counter / Timer Indicator (FXY Series).
-
- Manufacturer: AUTONICS
- Model / Part Number: LA8N-BF
- Display: 8-digit, 7-segment LCD panel with an 8.7 mm character height for clear readability.
- Input Signal Type: Universal AC/DC voltage input, which accepts signals ranging from 24V to 240V AC or 6V to 240V DC.
- Counting Speed: Maximum of 20 cps (counts per second).
- Operation Method: Count-up indicator (keeps adding numbers sequentially).
- Size & Mounting: Compact DIN size (W48mm × H24mm × L54mm) designed for standard panel cutouts.
- Environment Protection: IP66 rated front panel, making it dustproof and waterproof against low-pressure water streams.
-
- Manufacturer: AUTONICS
- Model / Part Number: LE3S
- Time Range: It can track time from 0.01 seconds up to 9,990 hours.
- Output Type: SPDT (Single Pole Double Throw) relay output rated at 250 VAC / 5A. This allows it to act as an automatic switch for another device.
- Size: Standard 1/16 DIN size (W48mm × H48mm × L67mm), making it compact enough to fit into tightly packed electrical control panels.
- Mounting: Built as an 8-pin plug type device. You will need a matching 8-pin socket (like a PG-08 or PS-08 base) to wire it up to a panel or DIN rail.
- ON Delay: Waits for a set amount of time after receiving a signal before turning on.
- OFF Delay: Keeps a machine running for a set time before turning it off.
- Flicker (Cycle): Continuously flashes a device on and off at set intervals (useful for warning lights or sirens).
- Interval Delay: Turns an output on immediately when triggered, keeps it on for the set duration, and then turns it off.
- Integration Time: Accumulates time over multiple short periods.
- The Numbers: Shows the current counting time. You can set it to count up from zero or count down from your target time.
- The Bar Graph: A small visual progress bar fills up in 5% steps to show you how close the timer is to finishing.
- Contact Status: Displays a graphic icon showing whether the internal switch is currently Open (NO) or Closed (NC).
- Start: Tells the timer to begin running.
- Reset: Instantly resets the current time count back to the beginning.
- Inhibit: Freezes the current count in place temporarily without resetting it.
-
- Manufacturer: AUTONICS
- Model / Part Number: LE4S
- Power Supply: 24–240 VAC (50/60 Hz) or 24–240 VDC
- Terminal Type: 8-pin plug
- Input Method: No-voltage NPN input
- Minimum Input Time: Selectable between 1 ms or 20 ms
- Return/Reset Time: Max 100 ms
- Control Output Type: Time-limit SPDT (Single Pole Double Throw) relay
- Contact Capacity: 5 A at 250 VAC / 30 VDC (resistive load)
- Output Modes: 10 variations including ON Delay, Interval, Flicker, ON-OFF Delay, and OFF Delay
- Time Operation: SIGNAL ON START (the timer begins when an electrical signal is received)
- Overall Time Range: Extremely wide window from 0.01 seconds up to 9999 hours
- Fine-Tuning: High-precision setting option down to 0.001-second units (for the 9.999s range)
- One-Shot Output Time: Configurable from 0.01 to 99.99 seconds
- Screen Display: 4-digit, 7-segment LCD screen with a bright backlight
- Counting Direction: Can count up or count down
- Data Protection: Includes a key-lock setting function to safely store configuration data
- Interface: Soft-touch front buttons for simple programming
-
- Manufacturer: Autonics
- Model / Part Number: MP5W-41
- Display: 5-digit, 7-segment, high-brightness red LED with a 14mm character height.
- Measurement Range: -19,999 to 99,999.
- Input Capabilities: Supports input frequencies from 0.0005Hz up to 50kHz. It is compatible with both Voltage input (PNP) and No-voltage input (NPN) proximity or photoelectric sensors.
- Power Supply: Universal 100–240VAC at 50/60Hz.
- Output Configuration: Features 3 triple relay control outputs for limit alerts or system automation triggers.
- Dimensions: Built for standard 96x48mm panels with a required panel cutout of roughly 92x45mm.
-
- Manufacturer: Autonics
- Model / Part Number: MP5W-4N
- Display Type: 5-digit 7-segment red LED
- Character Height: 14 mm (0.55 inches) for easy reading
- Display Range: -19,999 to 99,999
- Power Supply: 100–240 VAC (50/60 Hz)
- Input Options: Supports both PNP (voltage) and NPN (no-voltage) sensor inputs
- Physical Size: Standard 1/8 DIN panel size (Dimensions: 96mm wide x 48mm high)
-
- Manufacturer: Autonics
- Model / Part Number: MT4W-DV-41
- Measurement Type: DC Voltage
- Power Supply: 100–240 VAC (~ 50/60 Hz)
- Display Method: 4-digit, 7-segment red LED display (character height: 14.2 mm)
- Display Range: -1999 to 9999
- Selectable Input Ranges: 0-500V, 0-100V, 0-50V, 0-10V, 0-5V, 0-1V, 0-250mV, 0-50mV
- Main Control Output: 3 Relay Outputs (HI, GO, LO comparative values)
-
REQUEST A QUOTE
- Manufacturer: AUTONICS
- Model / Part Number: MT4Y-AA-4N
- Display Method: 4-digit 7-segment red LED Character height: 14.2mm
- Measurement Range: -1999 to 9999 Max allowable input: 110% Full Scale
- Monitored Variables: AC Current & Frequency Frequency range: 0.1 Hz to 9999 Hz
- Current Input Specs: Multi-range selectable 0-5A, 0-2.5A, 0-1A, 0-500mA, 0-250mA, 0-100mA, 0-50mA
- AC Measurement Type: AVG or RMS Selectable Average value or Root Mean Square
- Supply Voltage: 100–240 VAC ~ 50/60Hz Power consumption: Max 5 VA
- Main Output: Indicator Pure indication unit (No relay/transmission outputs)
- Sampling Cycle: 16.6 ms Powered by a Sigma Delta (ΣΔ) ADC
- Dimensions: W72mm × H36mm panel size.
- Panel Cutout: 68mm (Width) × 31.5mm (Height).
- Operating Temperature: -10°C to 50°C (Storage: -20°C to 60°C).
- Ambient Humidity: 35% to 85% RH.
- Key Features: Zero-point adjustment, peak display value monitoring, high display correction, and external hold function.
-
REQUEST A QUOTE
- Manufacturer: AUTONICS
- Model / Part Number: MT4Y-DA-44
- Display Type: 4-digit, 7-segment red LED with a 14.2mm character height.
- Display Range: -1999 to 9999.
- Measurement Target: DC Current.
- Input Specifications: Selectable ranges including 0-5A, 0-2A, 0-500mA, 0-200mA, 0-50mA, 4-20mA, 0-5mA, and 0-2mA.
- Power Supply: 100–240 VAC (~50/60 Hz).
- Main Output: Relay contact output (LOW OUT).
- Sub Output: RS485 communication interface.
- Sampling Cycle: 50 ms.
- A/D Conversion Method: ΣΔ (Sigma Delta) ADC.
- Dimensions & Form Factor: DIN W72 x H36mm panel meter.
- Environment Limits: Operating temperature of -10°C to 50°C (Storage: -20°C to 60°C).
- Certifications: CE, cURus.
- High/Low Limit Scaling: Allows adjusting the display output relative to input ranges.
- Advanced Monitoring: Features peak display value monitoring and correction.
- Hold & Zero-Point Functions: Includes an external hold function and digital zero-point configuration adjustments.
