Showing 961–976 of 1357 results
-
REQUEST A QUOTE
- Model / Series: MICO+ 4.10 (Intelligent Power Distribution Module)
- Number of Channels: 4 independent monitoring channels
- Input Voltage: Nominal 24 V DC (Operating range: 18–30 V DC)
- Output Current Settings: Adjustable per channel: 4 A, 6 A, 8 A, or 10 A
- Inrush Capacity: Max. 20 mF per channel (ideal for high-capacitive loads)
- Termination / Connection: Maintenance-free, vibration-resistant Spring Clamp Terminals
- Mounting Type: 35mm DIN Rail Mount (Net width: 70 mm)
- Status Indicators: Multi-color LED status indicators for each individual channel
- Control Functions: Remote start/reset, switch-off capabilities, and group alarm contact
- Operating Temperature: 0°C to +55°C
Brand New MURR 9000-41084-0401000 Distributor. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Code Number: 1797
- Outer Diameter: ø30 mm
- Maximum Motor Speed: 19,000 RPM (at 0.5 MPa / 71 PSI)
- Maximum Power Output: 130 W
- Air Consumption: 180 NL/min (6.29 CFM)
- Proper Air Pressure: 0.3 – 0.5 MPa (42 – 71 PSI)
- Net Weight: 298 g (excluding hoses)
- Modular System: Designed as a separate-type system. It can be combined with various Nakanishi ø30 mm spindles or speed reducers (such as the ARG-011E 1/4 speed reducer) depending on the torque requirements of the application.
- Thermal Management: Engineered to withstand long, continuous operation without significant heat generation.
- Noise Reduction: Equipped with an inline silencer to minimize exhaust noise during operation.
- Required Accessories: To run this motor safely, it must be paired with an Air Line Kit (AL-M1202 or AL-M1203BS2) providing filtered, regulated, and lubricated air.
- Type: Motor; Outer Diameter: φ30 mm; Motor speed: 19,000 min-1 (0.5 MPa); Max. power: 130 W; Proper air pressure: 0.3–0.5 MPa; Air…
Brand New NAKANISHI AM-3020R Vane-Type Air Motor (Air-Speed Series). In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Motor Type: Brushless DC Motor
- Outer Diameter: φ 30 mm
- Speed Range: 1,000 – 30,000 min⁻¹ (RPM)
- Housing Material: Stainless Steel (SUS416)
- Net Weight: 350 g (14.64 oz.) without cord
- Standard Accessories: Wrench (22 × 27): 1 pc.
- NSK Catalog Number: 11769
- Controller Requirement: This motor must be connected to a compatible NAKANISHI controller, such as the NSK America E3000 Controller. If it is hooked up to an older or incompatible legacy controller, the safety features will trigger and it will not rotate.
- Cord Limitations: The motor requires a specialized joint-type motor cord. Note that the long 25.3 ft / 8m cord (EMCD-3000J-8M) cannot be used with this torque motor.
- Variant Differences: EM-3030T vs. EM-3030T-J
Brand New NAKANISHI EM-3030T Motorized Spindle. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Manufacturer: NAKANISHI (Japan)
- Series: E3000 Series
- Part Number: EMCD-3000-6M
- Type: Motor Cord / Cable (Straight connection type at the spindle body end)
- Length: 6 meters (approx. 19.6 feet)
- Standard Accessories Included: Air hose and connector cap
- UNSPSC Code: 27112809
- Cable Model: Connection Design
Brand New NAKANISHI EMCD-3000-6M Spindle Cable. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Manufacturer: NAKANISHI Co., Ltd. (Japan)
- Part Number: EMCD-3000-8M
- Component Type: Spindle Motor Connection Cord / Cable
- Cord Length: 8 meters (approx. 26.6 feet)
- Cord Style: Straight Type (Connection at the body end)
- Standard Accessories: Integrated air hose, connector cap
- Integrated Air Cooling: The cable features a dual-purpose design containing both the electrical wiring and an integrated air hose. This supplies cooling air and purge air directly to the spindle to prevent overheating and repel dust or contaminants.
- System Requirements: It serves as a necessary component bridging the E3000 Controller and compatible brushless motor spindles.
- Compatible Motor Models: EM-3060, EM-3030T, EM30-S6000, EM25-S6000, and EM20-S6000.
- Usage Warning: Ensure proper variant pairing. For example, standard motor cords are designated exclusively for their corresponding series and should not be mismatched with variant sub-models (like specific J-type or A-type configurations) unless explicitly outlined by the manufacturer manual.
Brand New NAKANISHI EMCD-3000-8M Spindle Cable. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Manufacturer: NAKANISHI Inc. (NSK)
- Part Number (MPN): EMCD-3000A-6M (Catalog code: 1743)
- Cable Length: 6.0 Meters (approx. 19.6 feet)
- Connector Configuration: Angle Type (90° degree bend)
- System Compatibility: E3000 Series Motor Spindles
- Compatible Spindle Models: EM-3060, EM-3030T, EM30-S6000, EM25-S6000, EM20-S6000
- Standard Accessories: Air Hose & Connector Cap
- Spatial Optimization: The primary distinction of the "A" variant (EMCD-3000A) over the standard straight cord (EMCD-3000) is its 90° right-angle connector. This makes it ideal for compact CNC milling machines, robotic arms, and custom fixture blocks where a straight cable exit would interfere with machine walls or workpieces.
- Integrated Air Line: The cable assembly houses both the electrical conduits and the physical air hose lines. This dual structure supplies air purging directly to the spindle to prevent dust, coolant, and debris from infiltrating the bearings during high-rpm operations.
- Type: Motor Cord; Length: 4M: 4 m. 6M: 6 m. 8M: 8 m; Standard equipment and accessories: Air hose. Connector cap (Included); Compa…
Brand New NAKANISHI EMCD-3000A-6M Spindle Cable. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Manufacturer: NAKANISHI (NSK America)
- Part Number: EMCD-3000J-6M
- Actual Length: 5.7 meters (approx. 18.7 feet)
- Cord Type: Motor Cord (Joint Type)
- Standard Accessories: Air Hose & Connector Protection Cap
- Compatible Motors: EM-3060J, EM-3030T-J, EMS-3060K, EMS-3060A, EMR-3008K, EMA-3020K, EMA-3020S, EMSF-3060K, and EM-3080J.
Brand New NAKANISHI EMCD-3000J-6M Spindle Cable. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Spindle Type: 90° Standard Right Angle Spindle
- Outer Diameter: φ 30 mm
- Reduction Ratio: 1 / 1.5
- Spindle Accuracy / Runout: Within 2 μm to 3 μm
- Collet Capacity: CHK Series: φ 0.5 mm to φ 6.0 mm (Up to φ 1/4")
- Net Weight: 580 g (1 lb. 4.46 oz.)
- NSK Catalog Number: ASE1579 (Formerly RAX-270E)
Brand New NAKANISHI RAX-271E Motorized Spindle. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Number of Ports: 2 high-speed CAN ports
- Transceiver: Philips TJA1041
- Maximum Baud Rate: 1 Mbps
- Driver Support: NI-RIO driver
- Port-to-Port Isolation: 60 V DC continuous (Measurement Category I up to 5,000 m altitude)
- Dielectric Withstand Voltage: 500 V RMS (verified by a 5-second test)
- Ingress Protection: IP40 rated
- Variant Distinction: 779429-01 denotes the standard version (not conformal coated).
- System Architecture: Operates exclusively within a CompactRIO chassis to interface directly with the backplane FPGA.
- Cabling Constraints: Follows ISO 11898 standards. It supports a total cable length of 40 meters at 1 Mb/s with a maximum stub length of 0.3 meters. Longer distances are possible at reduced bit rates.
- FPGA I/O Control Methods: Supports native programmatic functions within LabVIEW including Abort (cancel pending frame transmission), Reset (reinitialize port), Start/Stop Communication, and Wait for Transceiver Mode (handling wakeups or sleep states).
Brand New National Instruments NI 9853 779429-01 CAN Interface Module (C Series). In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Primary Function: High-Voltage Bar Boost CCFL Driver
- Operating Frequency: ~65 kHz (Typical for the modular family)
- Form Factor / Dimensions: Slim strip architecture (approx. 105.0 mm × 25.0 mm × 10.2 mm)
- Common Applications: CNC machines, medical monitoring equipment, HMI operator panels, and factory automation screens.
- Pin Number: Signal Name
- Main DC Power Supply Input: +12V DC Input line
Brand New NEC 104PW181 High Voltage Power Board. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Manufacturer: NEC LCD Technologies, Ltd. (NEC Corporation)
- Device Type: DC/AC Backlight Inverter Module
- Nominal Supply Current: 530 mA
- Operating Frequency: 65 kHz
- Output Capability: Supports 2-Lamp CCFL configurations
- Environmental Standards: RoHS Compliant, Lead-Free design
- Form Factor / Package: Compact integrated PCB module
- Cross-Compatibility: Drops in as an alternate model/upgrade for 104PW161, CXA-0308, and CXA-0543 (features enhanced operating temperature tolerance)
- High or Open: Backlight turns ON.
- Low: Backlight turns OFF.
Brand New NEC 104PW191 High Voltage Power Board. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Input Supply Voltage: 12.0 V DC (Nominal)
- Nominal Supply Current: 0.53 A (530 mA)
- Output Voltage: 520 V AC
- Output Current: 5.0 mA (0.005 A)
- Operating Frequency: 67.5 kHz
- Interface Connector: 12-pin module alignment
- Compliance: RoHS compliant, Lead-Free
- Recommended Action: When servicing a system utilizing the 104PW201, verify lamp integrity or proactively replace the dual CCFL lamps alongside the inverter.
- Benefits: Extends display lifespan to over 100,000 hours, lowers power draw, removes high-voltage points, and requires no soldering to adapt the original 12-pin wire harness.
Brand New NEC 104PW201 High Voltage Power Board. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Screen Size: 15.3 inches
- Resolution: 1280 × 768 pixels (WXGA format)
- Aspect Ratio: 15:9
- Brightness: 470 cd/m² (NITS)
- Contrast Ratio: 700:1
- Display Mode: SA-SFT, Normally Black, Transmissive
- Viewing Angle: Ultra-wide 88°/88°/88°/88° (Left/Right/Up/Down)
- Color Depth: Supports 262K or 16.7M colors (6-bit / 6-bit + Hi-FRC)
- Surface Treatment: Antiglare with a 3H hard coating
- Operating Temperature: Wide operational window of -10°C to +70°C
- Lamp Type: Edge-lit LED string system (4 strings total)
- Lamp Life: Rated for an extensive 70,000 hours of continuous use
- Input Voltage: Typical 28.4V (ranges from 25.7V minimum to 31.5V maximum)
- Interface Configuration: Utilizes a 10-pin connector system (SM10B-SHLS-TF)
Brand New NEC NL12876BC26-32D Industrial-Grade TFT-LCD Display Panel (NL12876 Series). In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Panel Size / Type: 10.4 inches (26.4 cm) diagonal / a-Si TFT-LCD, LCM
- Resolution / Aspect Ratio: 640 × 480 (VGA) / 4:3
- Surface Treatment: Clear or Antiglare, Hard coating (3H)
- Brightness (Typical): 450 cd/m² (Nits)
- Contrast Ratio: 600:1 (Typical)
- Display Colors: 262K (43% NTSC coverage)
- Signal Interface: CMOS (1 ch, 6-bit), 31 pins connector
- Input Voltage: 3.3V / 5.0V (Typical)
- Operating Temperature: -10°C to 70°C (14°F to 158°F)
- Storage Temperature: -20°C to 80°C (-4°F to 176°F)
Brand New NEC NL6448BC33-59D LCD Screens. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Model Series: HES (Hollow Shaft Series)
- Resolution: 2500 P/R (Pulses Per Revolution)
- Output Phase/Signals: 2M: A, B (90° phase difference) + Zero Signal (Z)
- Output Circuit Type: D: Line Driver Output (with complementary inverted signals Ā, B̄, Z̄)
- Supply Voltage: DC 4.75V – 5.25V (5V DC nominal)
- Current Consumption: 150 mA Maximum
- Max Response Frequency: 200 kHz
- Shaft Dimensions: 8mm (0.31 inches) blind hollow shaft
- Outer Diameter: 38mm (1.50 inches)
- Max Mechanical Speed: 6000 r/min (RPM)
Brand New NEMICON HES-25-2MD 2500P R Rotary Encoder. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
-
REQUEST A QUOTE
- Technical Attribute: Specification
- Encoder Type: Incremental Rotary Encoder
- Resolution: 500 pulses per revolution (PPR)
- Shaft Type / Diameter: Solid Shaft / φ 8 mm
- Dimensions: φ 50 mm (Diameter) × 34 mm (Length)
- Output Phase: A / B two-phase + Z (index) phase
- Output Type: Push-Pull output (with partial load short-circuit protection)
- Supply Voltage Range: DC 4.75V to 30V
- Max Response Frequency: 100 kHz
- Max Mechanical Speed: 5000 RPM
Brand New NEMICON NOC2-S500-2HC Rotary Encoder. In stock — ships worldwide within 5-10 days.
1-year warranty against manufacturing defects. Contact us for pricing — reply within 24 hours.
